Double Shaft Mixer Filter Screen Mixer

Filter screen mixer TWJH550 mix equipment for clay brick making line mixing machine

Double shaft mixer filter screen mixer TWJH550 mix equipment for clay brick making line mixing machine

TWJH550 front grid mixer extruder is a new product developed by our company on the basis of absorbing the advanced experience of similar products abroad, and it occupies a leading position among similar products in China.

The function of the front grid mixer: homogenize and mix raw materials through biaxial stirring; Through reamer extrusion, strengthen the mutual penetration of water between raw materials and improve the plasticity of materials.

It is equipped with a mesh plate to increase the resistance, thereby improving the kneading efficiency of the raw materials, and can filter the grass roots and bark in the soil, reducing the blockage of the brick machine mold and the probability of breaking the steel wire of the blank cutting machine.

It is especially suitable for thin-walled high-quality product.

The stencil is controlled by a hydraulic system, which can quickly clean and replace the stencil and improve production efficiency.

Working principle and structural characteristics:

The power is driven by the motor through the reducer and the gear pair of the gearbox to drive the two shafts of the mixer to rotate in opposite directions. The two shafts are respectively equipped with stirring knives with opposite directions. The stirring knife makes the material toss, shear and convectively mix; at the same time, the water spray system sprays mist water to the material, and mixes it with it. With the rotation of the stirring shaft, the stirring blade continuously stirs, mixes and homogenizes the raw materials, and continuously pushes the raw materials to the feeding port of the sealing cylinder. After the raw material enters the sealed cylinder, its density increases continuously due to the influence of the volume compression of the compressor head. During this process, the kneading effect between the mud materials further improves the homogenization effect on raw materials of different properties. Under the action of the thrust of the screw reamer, the mud is forced and continuously extruded from the wear-resistant mesh plate of the discharge port of the compressor head and falls into the next production process.

The main part of this series of equipment is mainly composed of transmission motor, pneumatic clutch, hard tooth surface reducer, gear box, stirring tank, stirring shaft, stirring knife, sealing cylinder, extrusion reamer, compressor head, sieve plate, hydraulic station, base and other parts composition. There is a water adding pipeline on the stirring tank, which is used to adjust the molding moisture content of the raw materials. A pneumatic clutch is arranged between the motor and the reducer, which is used for overload protection of frequent start and stop of the equipment. The cutter head and sieve plate of the stirring blade are cast with wear-resistant alloy, and are connected with the fixed seat by high-strength bolts, which is convenient for maintenance and replacement. The extrusion reamer and the inner and outer conical sleeves are all made of wear-resistant alloy steel, which is wear-resistant and easy to replace.

Grid front extruding mixer of technical paramerters:

Grid front extruding mixer for clay brick making plant machinery

Front grid extruding mixer machine in auto brick production line

BBT focuses on the core business development by concentrating on the professionalization strategy. We devote ourselves to integrating technical solutions of production line process design, thermal design, equipment R&D, trade,mechanical and electrical equipment installation, international engineering, project consultancy, technical service for producing sintered wall materials of fired perforated brick, paving block, facing brick, hollow block, insulating block, wall board.

BBT takes the market demand as guidance, creates the value for the customer as objective and sincerely provides:

1. Process design of directing setting, two times setting and firing technology(BBT masters core technology);

2. Wall boards production process technology;

3. Prefabricated walls production process technology;

4. Key equipment in raw materials treatment process: wet pan mill, high speed fine-pulverized roller;

5. Key equipment in molding process: extruding type mixer and filter mixer;

6. Equipment R&D and manufacturing of fully automatic cutting, marshalling, brick stacking, loading and unloading;

7. Equipment R&D and manufacturing of thermal running, thermal monitor and control system;

8. All types of fuel combustion and control systems;

9. Management services of brick & tile production technology.

With the love of brick, BBT will continue to take unremitting efforts to provide our clients with high standard brick making production line through continuous innovation and strict industrial chain development and management.